Airmar B60-20-MM 600W 20-Degree Tilt Bronze Thru-Hull Transducer Mix and Match
Airmar B60-20-MM 600W 20-Degree Tilt Bronze Thru-Hull Transducer Mix and Match
Buy now, pay later & Finance Options
Find Local Store
Low-profile tilted through-hull 600W 50/200kHz fishfinder
transducer
The B60 is a standard 50/200kHz transducer available with a tilt of
either 12 deg or 20 deg. The B117 is the equivalent of a B60 with
zero tilt.
Specifications:
| Type | Standard non-CHIRP fishfinder transducer |
| Frequency | 50 kHz / 200 kHz |
| Beam Width | 45 degrees at 50kHz / 12 degrees at 200kHz |
| Power Rating | 600 watts |
| Mounting | Low-profile through-hull |
| Housing | Bronze |
| Hull Aperture | 2.375' (60mm) |
| Usable Shaft Length | 2.70' (68.5mm) |
| Cable Length | 10 meters |
| Mix and Match | Yes |
| Temperature Sensor | Yes |
| Speed Sensor | ? |
| Retractable Insert | ? |
| Tilted | Yes |
| Status | In production |
| Reference Page |
Product Data Sheet
Base Models
These Mix and Match base models must be combined with a Mix and
Match cable for installation. The suffix '-MM' in the Gemeco part
number designates a Mix and Match base model.
| Transducer | Code | Airmar Part # | Tilt | Description |
|---|---|---|---|---|
 |
B60-12-MM | 31-554-2-01 | 12 degrees | B60 Base Transducer with 12 deg Tilt |
|
B60-20-MM | 31-556-2-01 | 20 degrees | B60 Base Transducer with 20 deg Tilt |
Mix and Match Cables
This transducer uses the Mix and Match system. Installation
requires two parts - a base model plus one of the Mix and Match
600W cables (MM) listed below.
Each base model has a 2 meter pigtail cable permanently attached.
This cable ends in an Airmar 5-pin female connector. The Mix and
Match cables are 9 meters long and have a male Airmar 5-pin
connector at one end (to connect to the transducer pigtail) and a
brand-specific connector at the other end (to connect to the
sounder or fishfinder). If an owner changes their fishfinder or
sounder, a different MM cable can be installed without disturbing
the transducer itself.
Kits are sold containing a base model and a Mix and Match cable.
For example, the B60-8G kit contains a base transducer and an MM-8G
cable.
| Cable Connector | Code | Airmar Part # | Length | Equipment |
|---|---|---|---|---|
 |
MM-0 | 33-480-01 | 9 meters | Bare wire applications |
 |
MM-10FUR | 33-564-01 | 9 meters | Furuno 10-pin |
 |
MM-10N | 22-860-01 | 9 meters | Northstar 490S, 491 |
 |
MM-2 | 33-240-02 | 9 meters | Raymarine ST50 |
 |
MM-3 | 33-244-01 | 9 meters | Older Fuji 3-pin |
 |
MM-5P-5P | 33-247-02 | 12 meters | Extension cable for 600W Mix and Match |
 |
MM-6DO | 33-271-01 | 9 meters | Garmin 6-pin depth-only |
|
MM-6DT | 33-966-01 | 9 meters | Garmin 6-pin |
 |
MM-6NAV | 33-914-01 | 9 meters | Navman/Northstar/Simrad 6-pin |
 |
MM-7 | 33-396-01 | 9 meters | Older Simrad, Raytheon, JRC 7-pin |
 |
MM-8 | 33-898-01 | 9 meters | Older Furuno/SiTex/Fuji 8-pin |
 |
MM-8G | 33-1178-01 | 9 meters | Garmin blue 8-pin |
 |
MM-8S | 33-628-01 | 9 meters | SiTex CVS, SVS |
 |
MM-DT-LOW | 33-636-01 | 9 meters | Lowrance/Simrad blue 7-pin |
 |
MM-FISO | 33-259-01 | 9 meters | Raymarine instruments with spade connectors |
 |
MM-HB | 33-630-01 | 9 meters | Humminbird #9 |
 |
MM-RAY | 33-621-01 | 9 meters | Raymarine DSM300 and equivalent |
 |
MM-RAYA | 33-622-01 | 9 meters | Raymarine current series 6/9-pin |
 |
MM-RCA | 33-238-02 | 9 meters | Datamarine |
Replacement Parts
| Part | Airmar Part # | Description |
|---|---|---|
 |
02-133-01 | Bronze Hull Nut |
 |
09-813-01 | Rubber Washer |
 |
60WR-1 | Crows Foot Wrench |
 |
60WR-2 | Single Handle Wrench |
 |
60WR-3 | Double Handle Wrench |
 |
60WR-4 | Single Handle Wrench |